Meyer Sound USW1P AMPLIFIED SUBWOOFER Online Hot Sale

Meyer Sound USW1P AMPLIFIED SUBWOOFER

Meyer Sound USW1P AMPLIFIED SUBWOOFER

Combining advanced loudspeaker technology with equally advanced power capabilities, the Meyer Sound USW-1P self-powered subwoofer provides flat, low-frequency response from 35 Hz to 180 Hz. The USW-1P performs seamlessly within a full range system, in conjunction with UPA-1P, UPA-2P and UPJ-1P loudspeakers. The USW-1P is also fully compatible with other Meyer Sound self-powered loudspeakers.

Features:

• Classic design configuration with proven heritage from USW-1 model
• High peak power capability for excellent transient reproduction
• Built-in crossover allows for simple daisy chain signal distribution and eliminates the need for external crossovers
• Compact cabinet satisfies a broad range of installation requirements
• Flat phase response for optimal crossover to mid/high systems

Specifications:

• Acoustical
  • Operating Frequency Range¹: 32 Hz – 200 Hz
  • Frequency Response²: 35 Hz – 180 Hz ±4 dB
  • Phase Response: 45 Hz – 155 Hz ±30°
  • Maximum Peak SPL³: 135 dB
  • Dynamic Range: >110 dB
• Coverage⁵
  • 360° single unit; varies for multiple units, depending on number and configuration
• Transducers
  • Low Frequency:
    • Two 15″ cone drivers
    • Nominal impedance: 4 Ω
    • Voice coil size: 2″
    • Power handling capability: 400 W
• Audio Input
  • Type: Differential, electronically balanced
  • Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
  • Connectors: Female XLR input with male XLR loop output or VEAM all-in-one connector (integrates AC, audio, and network)
  • Input Impedance: 10 kΩ differential between pins 2 and 3
  • Wiring:
    • Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
    • Pin 2: Signal +
    • Pin 3: Signal – (optional polarity reversal switch)⁶
    • Case: Earth ground and chassis
  • DC Blocking: Differential DC blocking up to maximum common mode voltage
  • CMRR: >50 dB, typically 80 dB (50 Hz – 500 Hz)
  • RF Filter: Common mode: 425 kHz; Differential mode: 142 kHz
  • TIM Filter: <80 kHz, integral to signal processing
  • Nominal Input Sensitivity: 0 dBV (1.0 V rms, 1.4 V peak) continuous is typically the onset of limiting for noise and music
  • Input Level: Audio source must be capable of producing +20 dBV (10 V rms, 14 V peak) into 600 Ω in order to produce maximum peak SPL over the operating bandwidth of the loudspeaker
• Amplifier
  • Two-channel complementary MOSFET output stages (class AB/bridged)
  • Output Power⁶: 550 W total
  • THD, IM, TIM: <.02%
  • Load Capacity: 4 Ω both channels
  • Cooling: Convection; 24 V DC output for optional external fan
• AC Power
  • Connector: PowerCon or VEAM
  • Voltage Selection: Automatic, continuous range from 90 V AC – 265 V AC
  • Safety Agency Rated Operating Range: 100 V AC – 240 V AC; 50/60 Hz
  • Turn-on and Turn-off Points: 90 V AC on, no turn-off, only fuse protected above 265 V AC⁷
  • Current Draw: Idle Current: .0.25 A rms (115 V AC); 0.13 A rms (230 V AC); 0.3 A rms (100 V AC)
  • Maximum Long-Term Continuous Current (>10 sec): 2.8 A rms (115 V AC); 1.4 A rms (230 V AC); 3.2 A rms (100 V AC)
  • Burst Current (<1 sec): 3.2 A rms (115 V AC); 1.6 A rms (230 V AC); 3.7 A rms (100 V AC)
  • Ultimate Short-Term Peak Current Draw: 5.0 A pk (115 V AC); 2.5 A pk (230 V AC); 5.8 A pk (100 V AC)
  • Inrush Current: <9 A pk (115 V AC and 230 V AC)
• RMS Network (optional)
  • Equipped with two-conductor twisted-pair network, reporting all operating parameters of amplifiers to system operator’s host computer
• Physical
  • Dimensions: 31.00″ w x 21.56″ h x 21.30″ d (787 mm x 548 mm x 541 mm)
  • Weight: 137 lbs (62.14 kg)
  • Enclosure: Premium birch plywood
  • Finish: Black textured
  • Protective Grille: Powder-coated hex-stamped steel, foam covering
  • Rigging: Three ring and stud pan fittings (on top); working load is 420 lbs (190.51 kg), based on a 5:1 safety factor