Meyer Sound MICA Powered Line Array Loudspeaker Hot on Sale

Title

Touring Gear – Used

Meyer Sound MICA Powered Line Array Loudspeaker

MICA™ is a self-powered, three-way loudspeaker designed for vertical curvilinear arraying. A member of the MILO® family of high-power curvilinear array loudspeakers, the MICA loudspeaker is ideal for applications that do not require quite as much power and throw distance as MILO and where weight and size is a concern. The MICA compact highpower curvilinear array loudspeaker is equally applicable in a wide variety of applications such as touring, rental and fixed installations. MICA provides an excellent complement to a MILO main system for tours that are playing a variety of venues, being used as sidefills for large arenas and sheds and as the main system for smaller venues.

Features:

Very high power-to-size ratio
Exceptional fidelity and transient response for intelligibility and high-impact
Seamless integration with MILO
Wide and even horizontal coverage pattern across the full bandwidth
QuickFly rigging system with new captive GuideALinks simplifies use in flown or ground-stacked arrays

Specifications:

Acoustical
- Operating Frequency Range¹: 60 Hz – 18 kHz
- Frequency Response²: 75 Hz – 17 kHz ±4 dB
- Phase Response: 1 kHz – 16 kHz ±30°
- Maximum Peak SPL³: 138 dB
- Dynamic Range: >110 dB
Coverage
- Horizontal Coverage: 100°
- Vertical Coverage: Varies, depending on array length and configuration
Crossover4
- 1000 Hz
Transducers
- Low Frequency:
  - Two high-power 10″ cone drivers with neodymium magnets
  - Nominal impedance: 4 Ω
  - Voice coil size: 2″
  - Power handling capability: 1200 W (AES)5; 1800 W peak⁶>
- High Frequency⁷:
  - 3″ compression driver
  - Nominal impedance: 8 Ω
  - Voice coil size: 3″
  - Diaphragm size: 3″
  - Exit size: 1.2″
  - Power handling capability: 360 W (AES)5; 720 W peak⁶
Audio Input
- Type: Differential, electronically balanced
- Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
- Connectors: Female XLR input with male XLR loop output or VEAMall-in-one connector (integrates AC, audio and network)
- Input Impedance: 10 kΩ differential between pins 2 and 3
- Wiring:
  - Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
  - Pin 2: Signal +
  - Pin 3: Signal –
  - Case: Earth ground and chassis
- DC Blocking: None on output, DC blocked through signal processing
- CMRR: >50 dB, typically 80 dB (50 Hz – 500 Hz)
- RF Filter: Common mode: 425 kHz; Differential mode: 142 kHz
- TIM Filter: Integral to signal processing (<80 kHz)
- Nominal Input Sensitivity: 0 dBV (1.0 V rms, 1.4 V peak) continuous is typically the onset of limiting for noise and music
- Input Level: Audio source must be capable of producing +20 dBV (10 V rms, 14 V peak) into 600 Ω in order to produce maximum peak SPL over the operating bandwidth of the loudspeaker
Amplifier
- Type: Four-channel complementary MOSFET output stages (class AB/H)
- Output Power⁸: 3020 W (four channels; 2 x 950 W, 2 x 560 W)
- Total Output⁹: 6000 W peak
- THD, IM, TIM: <.02%
- Load Capacity: 4 Ω low and mid channels; 8 Ω high channels
- Cooling: Forced air cooling, four fans (two ultrahigh-speed reserve fans)
AC Power
- Connector: 250 V AC NEMA L6-20 twistlock, IEC-309 male, PowerCon, or VEAM
- Voltage Selection: Automatic, two ranges, each with high-low voltage tap (uninterrupted)
- Safety Agency Rated Operating Range: 95 V AC – 125 V AC; 208 V AC – 235 V AC, 50/60 Hz
- Turn-on and Turn-off Points: 85 V AC – 134 V AC; 165 V AC – 264 V AC
- Idle Current: 1.1 A rms (115 V AC); 0.55 A rms (230 V AC); 1.3 A rms (100 V AC)
- Maximum Long-Term Continuous Current (>10 sec): 5.4 A rms (115 V AC); 2.7 A rms (230 V AC); 6.2 A rms (100 V AC)
- Burst Current (<1 sec)¹⁰: 8.7 A rms (115 V AC), 4.3 A rms (230 V AC), 10.0 A rms (100 V AC))
- Ultimate Short-Term Peak Current Draw: 24.6 A rms (115 V AC), 12.3 A rms (230 V AC), 28.3 A rms (100 V AC)
- Inrush Current: 7.1 A peak (115 V AC); 11 A rms (115 and 100 V AC), 15 A rms (230 V AC)
RMS Network (optional)
- Equipped with two-conductor twisted-pair network, reporting all operating parameters of amplifiers to system operator’s host computer
Physical
- Dimensions: 41.40″ w x 13.37″ h x 17.78″ d (1052 mm x 340 mm x 452 mm)
- Weight: 150 lbs (68.04 kg)
- Enclosure: Premium birch plywood
- Finish: Black textured
- Protective Grille: Powder-coated hex-stamped steel
- Rigging: MRF-MICA rigging frame, with captive GuideALink connectors and quick release pins

MAECENAS IACULIS

Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.

ADIPISCING CONVALLIS BULUM

Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
Diam parturient dictumst parturient scelerisque nibh lectus.

Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.

Meyer Sound MICA Powered Line Array Loudspeaker Hot on Sale