Meyer Sound UPQ2P Narrow Coverage Loudspeaker
Meyer Sound UPQ2P Narrow Coverage Loudspeaker
The self-powered UPQ-2P narrow coverage loudspeaker is a member of the award-winning UltraSeries family of loudspeakers. The UPQ-2P offers extremely high power output and low distortion, as well a focused beamwidth, which make it an ideal solution for small to mid-sized venues, houses of worship, theatres, and nightclubs — as either a stand-alone loudspeaker or as part of an array. The loudspeaker’s extended low-frequency headroom delivers a smooth sound over a wide operating frequency range of 55 Hz to 18 kHz. With its intuitive and versatile QuickFly® rigging options, the UPQ-2P fits smartly into touring and rental solutions or fixed applications.
Features:
- Narrow pattern affords precise coverage and arrayability
- Extraordinarily flat amplitude and phase response for tonal accuracy and precise imaging
- Integral pole mount and quick and easy QuickFly mounting options
- Constant-Q horn affords uniform response throughout coverage area
- Exceptional size to power ratio
- Consistent and predictable performance ensures accurate system design
Specifications:
- Acoustical
- Operating Frequency Range: 55 Hz – 18 kHz
- Frequency Response: 60 Hz – 16 kHz ±4 dB
- Phase Response: 490 Hz – 16 kHz ±45°
- Maximum Peak SPL: 136 dB
- Dynamic Range: >110 dB
- Coverage
- 50° horizontal x 50° vertical (–6 dB)
- 60° horizontal x 60° vertical (–10 dB)
- Crossover
- 690 Hz
- Transducers
- Low Frequency:
-
High-power 15″ cone driver with neodymium magnet
Nominal impedance: 2 Ω
Voice coil size: 4″
Power handling capability: 1200 W (AES) - High Frequency:
-
4″ compression driver
Nominal impedance: 8 Ω
Voice coil size: 4″
Diaphragm size: 4″
Exit size: 1.5″
Power handling capability: 250 W (AES)5
- Low Frequency:
- Audio Input
- Type: Differential, electronically balanced
- Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
- Connectors: Female XLR input with male XLR loop output or VEAM all-in-one connector (integrates AC, audio, and network)
- Input Impedance: 10 kΩ differential between pins 2 and 3
- Wiring:
- Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
- Pin 2: Signal +
- Pin 3: Signal – (optional polarity reversal switch)
- Case: Earth ground and chassis
- DC Blocking: Differential DC blocking up to maximum common mode voltage
- CMRR: >50 dB, typically 80 dB (50 Hz – 500 Hz)
- RF Filter: Common mode: 425 kHz; Differential mode: 142 kHz
- TIM Filter: Integral to signal processing (<80 kHz)
- Nominal Input Sensitivity: 0 dBV (1 V rms, 1.4 V pk) continuous average is typically the onset of limiting for pink noise and music
- Input Level: Audio source must be capable of producing a minimum of +20 dBV (10 V rms, 14 V pk) into 600 Ω to produce maximum peak SPL over the operating bandwidth of the loudspeaker
- Amplifiers
- Type: Two-channel complementary MOSFET output stages (class AB/H)
- Output Power: 1275 W (1 x 1000 W, 1 x 275 W)
- Total Output: 2550 W pea
- THD, IM, TIM: <.02 %
- Load Capacity: 2 Ω low channel, 8 Ω high channel
- Cooling: Convection at low to mid audio levels; fan-assisted only at high audio levels
- AC Power
- Connector: PowerCon with looping output or VEAM
- Voltage Selection: Automatic, two ranges, each with high-low voltage tap (uninterrupted)
- Safety Agency Rated Operating Range: 95–125 V AC; 208–235 V AC, 50/60 Hz
- Current Draw:
- Idle Current: 0.50 A rms (115 V AC); 0.28 A rms (230 V AC); 0.56 A rms (100 V AC)
- Max Long-Term Continuous Current (>10 sec): 3.90 A rms (115 V AC); 2.00 A rms (230 V AC); 4.40 A rms (100 V AC)
- Burst Current (<1 sec): 7.0 A rms (115 V AC); 3.9 A rms (230 V AC); 8.2 A rms (100 V AC)
- Ultimate Short-Term Peak Current Draw: 18.0 A pk (115 V AC); 10.5 A pk (230 V AC); 20.0 A pk (100 V AC)
- Inrush Current: 6.0 A pk (115 V AC); 8.4 A pk (230 V AC); 7.1 A pk (100 V AC)
- RMS Network (Optional)
- Equipped for two-conductor twisted-pair network, reporting all amplifier operating parameters to system operator’s host computer.
- Physical
- Dimensions:
- 19.00″ w x 28.27″ h x 18.18″ d
- (483 mm x 718 mm x 462 mm)
- Weight: 108 lbs (49 kg)
- Enclosure: Multi‑ply hardwood
- Finish: Black textured
- Protective Grille: Powder-coated hex-stamped steel, black mesh screen
- Rigging: Aluminum end plates on top and bottom with metric M10 threaded points; integral 1-1/2″ (38 mm) pole mount receptacle on bottom
- Dimensions:
