Meyer Sound UPJ-1P Powered Loudspeaker Online Sale

Meyer Sound UPJ-1P Powered Loudspeaker

Meyer Sound UPJ-1P Powered Loudspeaker

The UPJ-1P combines the advantages of self-powered systems with the placement and arraying flexibility afforded by a VariO rotatable horn. Though remarkably compact and lightweight, the UPJ-1P produces a robust peak power output of 128 dB SPL at 1 meter, making it suitable for use either singly as a primary loudspeaker or in multi-cabinet horizontal or vertical arrays. Applications include A/V presentations, small- to medium-sized main sound reinforcement systems, fill, delay, effects, under-balcony or under-canopy coverage and distributed systems. With a 10-inch low-mid neodymium magnet cone driver and a 0.75-inch exit, 3-inch diaphragm compression driver in the high-frequency section, the UPJ-1P delivers uncompromising quality and coverage. A two-channel class AB power amplifier with complementary MOSFET output stages provides a total output of 300 watts. The UPJ-1Ps cabinet incorporates aluminum end plates configured with multiple M8 threaded inserts to provide all the mounting points you’ll ever need. The end plates allow direct attachment to third party pole assemblies.

Features:

• Exceptional fidelity and extended high frequency performance
• Surprising power capability in a compact package
• Extraordinarily flat amplitude and phase response for tonal accuracy and precise imaging
• Constant-Q horn affords uniform response throughout the coverage area
• Predictable array performance ensures system design flexibility
• VariO horn allows loudspeakers to be oriented horizontally or vertically

Specifications:

• ACOUSTICAL
  • Operating frequency range: 55 Hz – 20 kHz
  • Free field frequency response: 66 Hz – 18 kHz ±4 dB
  • Phase response: ±45° 750 Hz to 18 kHz
  • Maximum peak SPL: 128 dB
  • Dynamic range: >110 dB
  • Coverage: 80° x 50°
  • Acoustical crossover: 2 kHz
• TRANSDUCERS
  • Low frequency:
    • One 10″ cone driver with neodymium magnet
    • Nominal impedance: 4 Ω
    • Voice coil size: 2″
    • Power-handling capability: 400 W (AES)
  • High frequency:
    • One 3″ compression driver
    • Nominal impedance: 16 Ω
    • Voice coil size: 3″
    • Diaphragm size: 3″
    • Exit size: 0.75″
    • Power-handling capability: 100 W (AES)
• AUDIO INPUT
  • Type: Differential, electronically balanced
  • Max. common mode range: ±15 V DC, clamped to earth for voltage transient protection
  • Connectors: Female XLR input with male XLR loop output
  • Input impedance: 10 kΩ differential between pins 2 and 3
  • Wiring:
    • Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
    • Pin 2: Signal +
    • Pin 3: Signal –
    • Case: Earth ground and chassis
  • DC Blocking: Differential DC blocking on input up to max. common mode voltage
  • CMRR: >50 dB, typically 80 dB (50 Hz – 500 Hz)
  • RF filter:
    • Common mode: 425 kHz
    • Differential mode: 142 kHz
  • TIM filter: <80 kHz, integral to signal processing
  • Nominal input sensitivity: 0 dBV (1 V rms, 1.4 V pk) continuous average is typically the onset of TPL limiting for noise and music.
  • Input level: Audio source must be capable of producing a minimum of +20 dBV (10 V rms, 14 V pk) into 600 Ω to produce maximum peak SPL over the operating bandwidth of the loudspeaker.
• AMPLIFIERS
  • Amplifier type: Two-channel complementary power MOSFET output stages (class AB)
  • Output power: 300 W total
  • THD, IM TIM: < .02%
  • Load capacity: 4 Ω low channel, 16 Ω high channel
  • Cooling: Forced air cooling over amplifier heatsink
• AC POWER
• AC power connector: PowerCon with looping output
• Voltage selection: Automatic
• Safety agency rated operating voltage: 100 V AC – 240 V AC; 50/60 Hz
• Turn on/turn off points: 90 V AC to 264 V AC; 50/60 Hz
• Current Draw
  • Idle current: 0.41 A rms (115 V AC); 0.33 A rms (230 V AC); 0.42 A rms (100 V AC)
  • Max. long-term continuous current (>10 sec): 3.2 A rms (115 V AC); 1.6 A rms (230 V AC); 3.7 A rms (100 V AC)
  • Burst Current (<1 sec): 5.0 A rms (115 V AC); 2.5 A rms (230 V AC); 5.8 A rms (100 V AC)
  • Ultimate Short-Term Peak Current Draw: 17 A pk (115 V AC); 8.5 A pk (230 V AC); 20 A pk (100 V AC)
  • Inrush Current: 15 A pk (115 V AC); 13 A pk (230 V AC); 15 A pk (100 V AC)