D&B Audiotechnik KSL8 Line Array System with KSL12 and SLSUB and D80 Amplifiers
D&B Audiotechnik KSL8 Line Array System with KSL12 and SLSUB and D80 Amplifiers
System includes:
24 KSL8 Line Array Loudspeakers
8 KSL12 Line Array Loudspeakers
16 SLSUB Line Array Subwoofers
24 D80 Amplified Controllers
Accessories (Contact a Sales Representative for more information)
D&B Audiotechnik KSL8 Loudspeaker
The KSL8 line array module produces an 80° constant directivity dispersion pattern in the horizontal plane over the entire operating bandwidth. The KSL8 houses two 10″ neodymium forward facing LF drivers and two side firing 8″ neodymium LF drivers. A coaxial mid-high section contains an MF horn with an 8″ driver and two 1.4″ exit, 3″ voice coil HF compression drivers mounted to a dedicated wave shaping device. SL-Series flying hardware comes with a patented workflow with integrated tension and compression rigging modes, allowing splay angles between cabinets from 0° to 10° in 1° increments. The loudspeakers are driven actively by two channels of an appropriate d&b amplifier. One channel powers the 10” LF drivers, the second channel powers all other components, which are passively crossed-over. This component geometry allows for a smooth crossover design with well-defined overlaps between adjacent bands providing consistent, even and very accurate horizontal dispersion. Due to the arrangement of the front and side firing LF drivers, seamless directivity control is maintained from the lowest frequencies the loudspeaker produces to above 18 kHz. Further expanding flexibility and catering for applications where smaller arrays are used and ArrayProcessing is not required, the KSL8 includes the option to link two cabinets in Line or Arc mode. The cabinets are constructed from marine plywood and have an impact and weather protected PCP (Polyurea Cabinet Protection) finish. The front and side panels incorporate rigid metal grills backed by an acoustically transparent and water repellent fabric. Each side panel incorporates a recessed handle, with additional handles provided at the rear.
Features:
- Constant directivity behaviour over the entire operating range using cardioid techniques in the lower range
- Exceptional broadband headroom
- Patented SL-Series flying hardware and method enables rapid deployment of KSL8 and KSL12 arrays directly from the Touring cart in either compression or tension rigging modes
- Requires only two amplifier channels; one channel drives the front facing 10″ LF drivers, while the other amplifier channel drives the passively crossed over 8″ side firing LF drivers, the 8” MF section and two HF drivers
- ArrayProcessing optimizes the level and tonal balance over the complete audience listening area
- For short arrays where ArrayProcessing is not required, two KSL loudspeakers can be linked and driven in the Arc / Line mode
- Efficient cabling system and amplifier rack assemblies
- Effective transport solutions
Specifications:
- System data:
- Frequency response (-5 dB standard): 54 Hz – 18 kHz
- Frequency response (-5 dB CUT mode): 75 Hz – 18 kHz
- Max. sound pressure with D40/D80/40D: 145 dB
- Cabinets per D40/D80/40D (ArrayProcessing): 2
- Cabinets per D40/D80/40D (Line or Arc mode): 4
- Loudspeaker data:
- Nominal impedance front LF: 8 ohms
- Nominal impedance side LF/MF/HF: 8 ohms
- Power handling capacity front LF (RMS/peak 10 ms): 450/1800 W
- Power handling capacity side LF/MF/HF (RMS/peak 10 ms): 250/1000 W
- Nominal dispersion angle (horizontal): 80 °
- Splay angle settings: 0 … 10° (1° increment)
- Components:
- 2 x 10″ front LF driver
- 2 x 8″ side LF driver
- 1 x 8″ MF driver
- 2 x 1.4″ exit compression driver with 3″ voice coil
- Passive crossover network
- Connections: 2 x NLT4 F/M
- Dimensions / weight:
- Dimensions (H x W x D): 330 x 1000 x 597 mm (13 x 39.4 x 23.5″)
- Weight: 58 kg (128 lb)
D&B Audiotechnik KSL12 Loudspeaker
The KSL12 line array module produces an 120° constant directivity dispersion pattern in the horizontal plane over the entire operating bandwidth. The KSL12 houses two 10″ neodymium forward facing LF drivers and two side firing 8″ neodymium LF drivers. A coaxial mid-high section contains an MF horn with an 8″ driver and two 1.4″ exit, 3″ voice coil HF compression drivers mounted to a dedicated wave shaping device. SL-Series flying hardware comes with a patented workflow with integrated tension and compression rigging modes, allowing splay angles between cabinets from 0° to 10° in 1° increments. The loudspeakers are driven actively by two channels of an appropriate d&b amplifier. One channel powers the 10” LF drivers, the second channel powers all other components, which are passively crossed-over. This component geometry allows for a smooth crossover design with well-defined overlaps between adjacent bands providing consistent, even and very accurate horizontal dispersion. Due to the arrangement of the front and side firing LF drivers, seamless directivity control is maintained from the lowest frequencies the loudspeaker produces to above 18 kHz. Further expanding flexibility and catering for applications where smaller arrays are used and ArrayProcessing is not required, the KSL12 includes the option to link two cabinets in Line or Arc mode. The cabinets are constructed from marine plywood and have an impact and weather protected PCP (Polyurea Cabinet Protection) finish. The front and side panels incorporate rigid metal grills backed by an acoustically transparent and water repellent fabric. Each side panel incorporates a recessed handle, with additional handles provided at the rear.
Features:
- Constant directivity behaviour over the entire operating range using cardioid techniques in the lower range
- Exceptional broadband headroom
- Patented SL-Series flying hardware and method enables rapid deployment of KSL8 and KSL12 arrays directly from the Touring cart in either compression or tension rigging modes
- Requires only two amplifier channels; one channel drives the front facing 10″ LF drivers, while the other amplifier channel drives the passively crossed over 8″ side firing LF drivers, the 8” MF section and two HF drivers
- ArrayProcessing optimizes the level and tonal balance over the complete audience listening area
- For short arrays where ArrayProcessing is not required, two KSL loudspeakers can be linked and driven in the Arc / Line mode
- Efficient cabling system and amplifier rack assemblies
- Effective transport solutions
Specifications:
- System data:
- Frequency response (-5 dB standard): 54 Hz – 18 kHz
- Frequency response (-5 dB CUT mode): 75 Hz – 18 kHz
- Max. sound pressure with D40/D80/40D: 144
- Cabinets per D40/D80/40D (ArrayProcessing): 2
- Cabinets per D40/D80/40D (Line or Arc mode): 4
- Loudspeaker data:
- Nominal impedance front LF: 8 ohms
- Nominal impedance side LF/MF/HF: 8 ohms
- Power handling capacity front LF (RMS/peak 10 ms): 450/1800 W
- Power handling capacity side LF/MF/HF (RMS/peak 10 ms): 250/1000 W
- Nominal dispersion angle (horizontal): 120 °
- Splay angle settings: 0 … 10° (1° increment)
- Components:
- 2 x 10″ front LF driver
- 2 x 8″ side LF driver
- 1 x 8″ MF driver
- 2 x 1.4″ exit compression driver with 3″ voice coil
- Passive crossover network
- Connections: 2 x NLT4 F/M
- Dimensions / weight:
- Dimensions (H x W x D): 330 x 1000 x 597 mm (13 x 39.4 x 23.5″)
- Weight: 58 kg (128 lb)
SL subwoofer
Large format flyable cardioid subwoofer
- Components 3 x 21″
- Dispersion: Cardioid
- SPL max: 144 dB
- Weight: 138 kg / 304 lb
D&B Audiotechnik D80 4-Channel 2000 Watt Audio Amplifier
The 2 RU four channel D80 amplifier is a high power density amplifier, ideally suited for use in both mobile and installation environments. It contains configurations for all d&b loudspeakers and a linear mode. The signal delay capability enables user definable settings of up to 10 s (= 3440 m/11286 ft) to be applied independently to each channel. The same applies to the two 16-band equalizers, providing optional parametric, asymmetric, shelving or notch filtering. The D80 incorporates a colour TFT touchscreen, offering quick access to the menu structure, while the rotary encoder can be used for fine adjustment. The front panel and the integrated touchscreen of the D80 amplifier is tilted up for ease of operation when the amplifier is below eye level. The equal ratio of signal input to amplifier output channels increases the application flexibility particularly for monitor, frontfill, or effect channel use. The LoadMatch function integrated within the D80 amplifier enables the electrical compensation of loudspeaker cable properties, without the need for an extra conductor. This results in an increased accuracy of audio reproduction over a bandwidth of up to 20 kHz, preserving the tonal balance when cable lengths of up to 70 m (230 ft) are used. The D80 incorporates Class D amplifiers utilizing a power supply with active Power Factor Correction (PFC) suitable for mains voltages 100 V/120 V/200 V/230 V, 50 – 60 Hz and maintains a stable output when used with weak or unstable mains supplies. An NL8 provides all outputs on a single connector, while individual outputs are optionally NL4 or EP5 connectors. RJ 45 and etherCON connectors enable access to the d&b Remote network via CAN-Bus and OCA/AES70 via Ethernet respectively.
Specifications:
- Digital Signal Processing
- Equalizer: 2 x 16-band PEQ/notch/shelving/asymmetric
- Latency analog and digital inputs: 0.3 msec.
- Delay setting: 0.3 – 10000 msec.
- Configurations: current d&b loudspeakers and linear mode
- Function switches: d&b loudspeaker specific circuits
- Frequency generator: Pink noise or Sine wave
- Sampling rate: 96 kHz/27 Bit ADC/24 Bit DAC
- Controls and indicators
- POWER: Mains power switch
- SCROLL/EDIT: Digital rotary encoder
- Display: Color TFT touchscreen, 3.5″/320 x 240 pixel
- ISP, GR, OVL A/B: Color TFT
- Connectors
- INPUT ANALOG (A1 – A4):3 pin XLR female
- ANALOG LINK (A1 – A4): 3 pin XLR male
- INPUT DIGITAL (D1/2, D3/4:):n 3 pin XLR female AES3
- DIGITAL LINK (Output): 3 pin XLR male
- Sampling Digital AES/EBU: 48 kHz/96 kHz
- Speaker outputs A/B/C/D: NL4, optional EP5
- 4 Channel output: NL8
- CAN: 2 x RJ 45 parallel
- ETHERNET: 2 x etherCON®, 10/100 Mbit Ethernet
- Mains connector: powerCON®-HC
- Data (linear setting with subsonic filter)
- Maximum output power per channel (THD+N < 0.5%, all channels driven)
- CF = 6 dB at 4 / 8 ohms: 4 x 2600/2000 W
- CF = 12 dB at 4 / 8 ohms: 4 x 4000/2000 W
- S/N ratio (unweighted, RMS)
- Analog input: –
- Digital input: > 114 dBr
- Power supply
- Type: Autosensing switch mode power supply with active Power Factor Correction (PFC)
- Rated mains voltage high range: 208 – 240 V, 50 – 60 Hz
- Rated mains voltage low range: 100 – 127 V, 50 – 60 Hz
- Dimensions / weight
- Dimensions (H x W x D): 2 RU x 19″ x 530.5 mm/20.9″
- Weight: 19 kg/42 lbs.
