Meyer Sound M1D Powered Line Array Loudspeaker with Camlinks
Meyer Sound M1D Powered Line Array Loudspeaker
(Camlinks Included)
The Meyer Sound M1D ultra-compact curvilinear array loudspeaker brings the singular advantages of self-powered line arrays to sound reinforcement applications in small and mid-sized venues. The exceptionally compact enclosure enables sound designers to achieve high output, precise pattern control with very low distortion from a lightweight and unobtrusive system. The M1D provides a substantial peak SPL of 125 dB at 1 meter with an operating frequency range of 60 Hz – 18 kHz and is designed specifically for implementing vertical curvilinear arrays of up to 16 cabinets having 0- to 8-degree splay between adjacent units. This design affords the flexibility to tailor vertical coverage by varying the number and splay of cabinets in the array while maintaining a consistent 100° horizontal coverage.
Features:
- Extremely compact and lightweight; forms virtually “invisible” PAs
- Very flat response for exceptional accuracy and imaging
- Constant-Q horn assures uniform coverage
- Unique crossover design eliminates mid-range combing
- Seamless integration with other M Series models
Specifications:
- ACOUSTICAL
- Operating Frequency Range: 60 Hz – 18 kHz
- Frequency Response: 75 Hz – 15 kHz ±4 dB
- Phase Response: 800 Hz – 12 kHz ±45°
- Maximum Peak SPL: 125 dB
- Dynamic Range: >110 dB
- COVERAGE
- Horizontal Coverage: 100°
- Vertical Coverage: Varies, depending on array length and configuration; for a single loudspeaker, 10° minimum
- CROSSOVER
- 1900 Hz
- TRANSDUCERS
- Low Frequency:
- Two 5″ cone drivers
- Nominal impedance: 8 Ω
- Voice coil size: 1″
- Power-handling capability: 200 W (AES)
- High Frequency:
- Three 0.75″ metal dome tweeters with neodymium magnets
- Nominal impedance: 8 Ω
- Voice coil size: 20 mm
- Power-handling capability: 15 W (AES)
- Low Frequency:
- AUDIO INPUT
- Type: Differential, electronically balance
- Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient pro
- Connectors: Female XLR input with male XLR loop output
- Input Impedance: 10 kΩ differential between pins 2 and 3
- Wiring:
- Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audiofrequencies
- Pin 2: Signal +
- Pin 3: Signal –
- Case: Earth ground and chassis
- DC Blocking: Differential DC blocking up to max common mode voltage
- CMRR: >50 dB, typically 80 dB (50 Hz – 500 Hz)
- RF Filter:
- Common mode: 425 kHz
- Differential mode: 142 kHz
- TIM Filter: Integral to signal processing (<80 kHz)
- Nominal Input Sensitivity: 0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
- Input Level: Audio source must be capable of producing of +20 dBV (10 V rms, 14 V peak) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker
- AMPLIFIER
- Type: Two-channel complementary MOSFET output stages (class AB/bridged)
- Output Power: 500 W total
- THD, IM, TIM: <.02%
- Load Capacity: 4 Ω low channel, 2 Ω high channel
- Cooling: Forced air cooling over amplifier heatsink
- AC POWER
- Connectors:PowerCon with looping output
- Voltage Selection: Automatic
- Safety Agency Rated Operating Range: 100 V AC – 240 V AC; 50/60 Hz
- Turn-on and Turn-off Points: Continuous 90 V AC – 264 V AC; 50/60
- Current Draw: Idle Current: 0.41 A rms (115 V AC); 0.33 A rms (230 V AC); 0.42 A rms (100 V AC)
- Max Long-Term Continuous Current (>10 sec): 3.2 A rms (115 V AC); 1.6 A rms (230 V AC); 3.7 A rms (100 V AC)
- Burst Current (<1 sec): 5.0 A rms (115 V AC); 2.5 A rms (230 V AC); 5.8 A rms (100 V AC)
- Ultimate Short-Term Peak Current Draw: 17 A pk (115 V AC); 8.5 A pk (230 V AC); 20 A pk (100 V AC)
- Inrush Current: 15 A pk (115 V AC); 13 A pk (230 V AC); 15 A pk (100 V AC)
- RMS NETWORK
- Equipped for two conductor twisted-pair network, reporting all operating parameters ofamplifiers to system operator’s host computer.
- PHYSICAL
- Dimensions:
- 23.04″ W x 7.12″ H x 8.50″ D
- (585 mm x 181 mm x 216 mm)
- Weight: 31 lbs (14.06 kg); shipping: 35 lbs (15.88 kg)
- Enclosure: Multi-ply hardwood
- Finish: Black textured
- Protective Grille: Powder-coated hex stamped steel
- Rigging: QuickFly® MRF-1D rigging frame
- Dimensions:
