Meyer Sound Melodie Powered Line Array Speaker Fashion

Meyer Sound Melodie Powered Line Array Speaker

Meyer Sound Melodie Powered Line Array Speaker

The self-powered M’elodie ultracompact high-power curvilinear array loudspeaker is a member of the popular MILO® family of loudspeakers. Its extended high-frequency headroom gives it a smooth sound over its wide operating frequency range of 70 Hz to 18 kHz. This headroom combines with a 100-degree horizontal coverage pattern to provide detailed resolution of delicate transient information across a broad coverage area.

Features:

• Exceptional power-to-size ratio
• Wide and even horizontal coverage pattern
• Very small footprint keeps a low profile appearance
• Seamless integration with MICA
• QuickFly rigging with captive GuideALinks simplifies use in flown or groundstacked arrays, alone or with MICA and/or 600-HP subwoofer

Specifications:

• ACOUSTICAL
  • Operating frequency range: 70 Hz – 18 kHz
  • Frequency response: 76 Hz – 16 kHz ±4 dB
  • Phase response: 1.5 kHz – 16 kHz ±30°
  • Maximum peak SPL: 131 dB
  • Dynamic range: >110 dB
  • Acoustical crossover: 1100 Hz
• COVERAGE
  • Horizontal coverage: 100°
  • Vertical coverage: Varies, depending on array length and configuration
• TRANSDUCERS
  • Low/low-mid:
    • frequency: Two 8” cone drivers with neodymium magnets
    • Nominal impedance: 4 Ω
    • Voice coil size: 1.5”
    • Power handling capability: 600 W (AES); 900 W peak
  • High frequency:
    • 3” compression driver
    • Nominal impedance: 8 Ω
    • Voice coil size: 3”
    • Diaphragm size: 3”
    • Exit size: 1.2”
    • Power handling capability: 180 W (AES); 360 W peak
• AUDIO INPUT
  • Type: Differential, electronically balanced
  • Max. common mode range: ±15 V DC, clamped to earth for voltage transient protection
  • Connectors: Female XLR input with male XLR loop output or VEAM all-in-one connector (integrates AC, audio, and network)
  • Input impedance: 10 kΩ differential between pins 2 and 3
  • Wiring:
    • Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
    • Pin 2: Signal +
    • Pin 3: Signal –
    • Case: Earth ground and chassis
  • DC Blocking: Differential DC blocking up to max common mode voltage
  • CMRR: >50 dB, typically 80 dB (50 Hz – 500 Hz)
  • RF filter:
    • Common mode: 425 kHz
    • Differential mode: 142 kHz
  • TIM filter: <80 kHz, integral to signal processing
  • Nominal input sensitivity: 0 dB V (1 V rms, 1.4 V pk) continuous is typically the onset of limiting for noise and music.
  • Input level: Audio source must be capable of producing +20 dBV (10 V rms, 14 V pk) into 600 Ω in order to produce maximum peak SPL over the operating bandwidth of the loudspeaker
• AMPLIFIERS
  • Amplifier type: Three-channel complementary MOSFET output stages (class AB/H)
  • Output power: 1275 W (three channels; 2 x 500 W, 1 x 275 W); 2550 W peak10
  • THD, IM TIM: < .02%
  • Load capacity: 4 Ω low and mid; 8 Ω high channels
  • Cooling: Convection cooled
• AC POWER
  • AC power connector: PowerCon with looping output or VEAM all-in-one connector (integrates AC, audio and network)
  • Voltage selection: Automatic, two ranges, each with high-low voltage tap (uninterrupted)
  • Safety agency rated operating voltage: 95 V AC – 125 V AC, 208 V AC – 235 V AC, 50/60 Hz
  • Turn on/turn off points: 85 V AC – 134 V AC; 165 V AC – 264 V AC
  • Idle current: 0.680 A rms (115 V AC), 0.360 A rms (230 V AC), 0.760 A rms (100 V AC)
  • Max. long-term continuous current (>10 sec): 2.3 A rms (115 V AC); 1.2 A rms (230 V AC); 2.6 A rms (100 V AC)11
  • Burst Current (<1 sec): 4 A rms (115 V AC), 2 A rms (230 V AC), 4.5 A rms (100 V AC)
  • Ultimate Short-Term Peak Current Draw: 13 A pk (115 V AC), 6.5 A pk (230 V AC), 15 A pk (100 V AC)
  • Inrush Current :10 A pk (115 and 100 V AC), 18 A pk (230 V AC)
• RMS NETWORK
  • Equipped with two-conductor twisted-pair network, reporting all operating parameters of amplifiers to system operator’s host computer.
• PHYSICAL
  • Enclosure: Premium birch plywood
  • Finish: Black textured
  • Protective grille: Powder-coated, hex-stamped steel, black mesh
  • Rigging: QuickFly rigging with four captive GuideALinks in the bottom corners of two aluminum and steel end frames, secured with quick-release pins
  • Dimensions: 28.54 w x 9.19 h x 12.75 d (724.84 mm x 233.31 mm x 323.85 mm)
  • Weight: 62 lbs (28.12 kg)