Meyer Sound MINA Powered Line Array Loudspeaker on Sale

Meyer Sound MINA Powered Line Array Loudspeaker

Meyer Sound MINA Powered Line Array Loudspeaker

The MINA™ compact curvilinear array loudspeaker is the smallest member of the industry-leading MILO® family of loudspeakers from Meyer Sound. Measuring just over a foot and a half wide (half a meter) and weighing only 41.2 lbs (18.69 kg), MINA is ideal for use in low-profile, high-power curvilinear array systems and an excellent choice for small theatres, theme parks, houses of wor-ship, AV systems, and any venue where size and weight are concerns and exceptional fidelity a requirement.

Features:

• Small footprint and narrow width ideal for small venues and fill applications
• Exceptional fidelity and transient response for intelligibility and high impact
• High power-to-size ratio
• Wide, even horizontal coverage pattern
• Flexible rigging options
• Seamless integration with M’elodie, MICA, and the 500-HP subwoofer
• QuickFly rigging with captive GuideALinks for flown and ground-stacked arrays, with additional MINAs, or with M’elodies or 500-HPs

Specifications:

• Acoustical
  • Operating Frequency Range¹: 66 Hz – 18 kHz
  • Frequency Response²: 70 Hz – 17.5 kHz ±4 dB
  • Phase Response: 1 kHz – 18 kHz ±30°
  • Maximum Peak SPL³: 128 dB
  • Dynamic Range: >110 dB
• Coverage
  • Horizontal Coverage: 100°
  • Vertical Coverage: Varies, depending on array length and configuration
• Crossover4
  • 760 Hz
• Transducers
  • Low Frequency:
    • Two 6.5″ cone drivers with neodymium magnets
    • Nominal impedance: 4 Ω
    • Voice coil size: 1.5″
  • High Frequency⁵:
    • 3″ compression driver
    • Nominal impedance: 8 Ω
    • Voice coil size: 3″
    • Diaphragm size: 3″
    • Exit size: 1.2″
• Audio Input
  • Type: Differential, electronically balanced
  • Maximum Common Mode Range: ±15 V DC
  • Connectors: XLR female input with XLR male loop output
  • Input Impedance: 10 kΩ differential between pins 2 and 3
  • Wiring:
    • Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
    • Pin 2: Signal +
    • Pin 3: Signal –
    • Case: Earth ground and chassis
  • DC Blocking: Differential DC blocking up to the maximum common mode voltage
  • CMRR: >50 dB, typically 80 dB (50 Hz – 500 Hz)
  • RF Filter: Common mode: 425 kHz; Differential mode: 142 kHz
  • TIM Filter: Integral to signal processing (<80 kHz)
  • Nominal Input Sensitivity: 0 dBV (1.0 V rms, 1.4 V peak) continuous is typically the onset of limiting for noise and music
  • Input Level: Audio source must be capable of producing +20 dBV (10 V rms, 14 V peak) into 600 Ω in order to produce maximum peak SPL over the operating bandwidth of the loudspeaker
• Amplifier
  • Type: Three-channel, Class-D
  • Output Power⁶: 975 W (three channels; 2 x 375 W, 1 x 225 W)
  • Total Output⁷: 1950 W peak
  • THD, IM, TIM: <.02%
  • Load Capacity: 4 Ω low channels; 8 Ω high channel
  • Cooling: Convection
• AC Power
  • Connector: PowerCon with loop output
  • Voltage Selection: Automatic, continuous from 90–265 V AC
  • Safety Agency Rated Operating Range: 100–240 V AC, 50/60 Hz
  • Turn-on and Turn-off Points:
    • 90 V AC turn-on, no turn-off
    • Internal fuse-protection above 265 V AC
  • Idle Current: 0.256 A rms (115 V AC); 0.249 A rms (230 V AC); 0.284 A rms (100 V AC)
  • Maximum Long-Term Continuous Current (>10 sec): 1.26 A rms (115 V AC); 0.66 A rms (230 V AC); 1.50 A rms (100 V AC)
  • Burst Current (<1 sec)⁹: 3.24 A rms (115 V AC), 1.74 A rms (230 V AC), 4.02 A rms (100 V AC)
  • Ultimate Short-Term Peak Current Draw: 10.4 A peak (115 V AC), 5.2 A peak (230 V AC), 11.1 A peak (100 V AC)
  • Inrush Current: 7.1 A peak (115 V AC); 16.8 A peak (115 V AC), 20.0 A peak (230 V AC), 15.0 A peak (100 V AC)
• RMS Network (optional)
  • Equipped with two-conductor twisted-pair network, reporting all operating parameters of amplifiers to system operator’s host computer
• Physical
  • Dimensions: 20.27″ w x 8.38″ h x 15.32″ d with rigging pins (515 mm x 213 mm x 389 mm)
  • Weight: 41.2 lbs (18.69 kg)
  • Enclosure: Premium birch plywood
  • Finish: Black textured
  • Protective Grille: Powder-coated, hex-stamped steel with black mesh
  • Rigging: End frames with four captive GuideALinks, secured with 0.25″ x 0.53″ quick-release pins; metric M6 attachment points for optional MYA‑MINA mounting yoke and MUB‑MINA U-bracket