Meyer Sound UPQ-D1 Large Point-Source Loudspeaker with 5-Pin XLR
Meyer Sound UPQ-D1 Large Point-Source Loudspeaker with 5-Pin XLR
The UPQ-D1 offers an extremely consistent polar response and a gentle coverage rolloff that extends uniformly out to its ‑10 dB points of 100° by 60°. The horn’s smooth and consistent performance is the result of meticulous research in Meyer Sound’s anechoic chamber, and it exhibits a remarkably consistent beamwidth in both the horizontal and vertical planes. The UPQ‑D1 horn also delivers uniform attenuation for all frequencies outside the specified beamwidth.
Features:
- Wide horizontal pattern covers broad listening areas and focused vertical pattern allows precise coverage
- Highly energy efficient amplifier with sophisticated digital signal processing that provides extraordinarily flat amplitude and phase response for tonal accuracy and precise imaging
- Integral stand mount and QuickFly mounting options facilitate rigging
- Constant-Q horn affords uniform response throughout coverage area
- Exceptional size to power ratio provides application flexibility
- Consistent and predictable performance ensures accurate system design
Specifications:
- Acoustical:
- Operating Frequency Range: 55 Hz – 18 kHz
- Frequency Response: 58 Hz – 18 kHz ±4 dB
- Phase Response: 80 Hz – 18 kHz ±45°
- Linear Peak SPL: 135.5 dB with crest factor >17 dB (M-noise), 132 dB (Pink noise), 135 dB (B-noise)
- Coverage:
- Horizontal Coverage: 80° horizontal x 50° vertical (-6 dB)
- Vertical Coverage: 100° horizontal x 60° vertical (-10 dB)
- Transducers:
- Low Frequency: One high-power 15-inch cone driver with neodymium magnet; 2 Ω nominal impedance
- High Frequency: One 4-inch diaphragm compression driver; 8 Ω nominal impedance
- Audio Input:
- Type: Differential, electronically balanced
- Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
- Connectors: 5-pin XLR connectors to accommodate both balanced audio and RMS signals
- Input Impedance: 10 kΩ differential between pins 2 and 3
- Wiring:
- Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
- Pin 2: Signal +
- Pin 3: Signal –
- Pin 4: RMS (polarity insensitive)
- Pin 5: RMS (polarity insensitive)
- Case: Earth ground and chassis
- Nominal Input Sensitivity: 0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
- Input Level: Audio source must be capable of producing of +20 dBV (10 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker.
- Amplifier:
- Type: Two-channel, Class-D
- Total Output Power: 2250 W peak
- THD, IM, TIM: < 0.02%
- Cooling: Convection
- AC Power:
- Connectors: PowerCON 20 input with loop output
- Automatic Voltage Selection: 90–265 V AC, 50–60 Hz
- Safety Rated Voltage Range: 100–240 V AC, 50–60 Hz
- Turn-on and Turn-off Points: 90 V AC turn-on; no turn-off; internal fuse-protection above 265 V AC
- Current Draw:
- Idle Current: 0.27 A rms (115 V AC); 0.25 A rms (230 V AC); 0.29 A rms (100 V AC)
- Maximum Long-Term Continuous Current (>10 sec): 2.0 A rms (115 V AC); 1.0 A rms (230 V AC); 2.3 A rms (100 V AC)
- Burst Current (<1 sec): 3.7 A rms (115 V AC); 1.9 A rms (230 V AC); 4.3 A rms (100 V AC)
- Maximum Instantaneous Peak Current: 8.2 A pk (115 V AC); 4.2 A pk (230 V AC); 9.3 A pk (100 V AC)
- Inrush Current: < 20 A peak
- Physical:
- Dimensions: W: 19.00 in (483 mm) x H: 28.15 in (715 mm) x D: 18.18 in (462 mm)
- Weight: 95 lb (43 kg)
- Enclosure: Premium multi-ply birch with slightly textured black finish
- Protective Grille: Powder-coated, hex-stamped steel with black mesh
- Rigging: Aluminum end plates on top and bottom with metric M10 threaded points; integral 1.5-inch (38 mm) pole mount receptacle on bottom
